Search found 151 matches: Ace II
Searched query: ace ii
ignored: ii
- Sun Jan 02, 2022 2:08 am
- Forum: CBoat C Forum
- Topic: Minicell Foam Adhesive?
- Replies: 2
- Views: 10936
Re: Minicell Foam Adhesive?
My go-to has been "red can" DAP / Weld wood contact cement, most often from my local ACE hardware.
- Tue Sep 17, 2019 2:01 am
- Forum: Boats and Gear for Sale
- Topic: Tomahawk C2 and Wildwater C1 for sale
- Replies: 0
- Views: 16667
Tomahawk C2 and Wildwater C1 for sale
... bothered me). Asking $650 -Roock Schmidt? Wildwater C1 - I think it is a Bala or Bala Mezzana, but could be a No Name. FAR more stable than my old Ace III that's for sure! Wayners old boat as I recall correctly. A few very well done patches but ready to paddle. Asking $650 Both located in Queensbury, ...
- Sat Aug 11, 2018 2:39 am
- Forum: CBoat C Forum
- Topic: gluing vinyl d ring patches to royalex
- Replies: 13
- Views: 17758
Re: gluing vinyl d ring patches to royalex
... spot. I don't have a dremmel so I use an air grinder. The stone is a 1 inch cone looking thing and I only use the side of the cone. I got mine at Ace for about $5. Use a washable marker, trace where your going to place it and the dremmel is easy to keep within the lines, it is very easy to get ...
- Tue Jun 20, 2017 3:08 pm
- Forum: CBoat C Forum
- Topic: Wildwater Boat
- Replies: 11
- Views: 22337
Re: Wildwater Boat
... probably less than a Sea Wind but more in that range. I have paddled an Ace II (not III) that I used to have in the ocean some. The downsides are wind (as edg noted) and ...
- Mon Jun 12, 2017 11:11 pm
- Forum: CBoat C Forum
- Topic: Wildwater Boat
- Replies: 11
- Views: 22337
Re: Wildwater Boat
... way. They are also rare as hen's teeth. If I was tilting at this particular windmill (with my own modest skill set) I would try to find an old Ace III. This has the same/very similar hull as the Tiptop, but a much lower bow deck. I suspect there are some out there, but I have no idea where. ...
- Wed Mar 22, 2017 7:01 pm
- Forum: CBoat C Forum
- Topic: Zet Raptor C1 conversion
- Replies: 12
- Views: 18335
Re: Zet Raptor C1 conversion
I'm using a Level Six Ace kayak deck on all ZET C1 models (the DirectorC1 is my primary boat), and each boat has about an extra inch added to it's saddleback. The tunnel offset isn't out enough to concern me. It's challenging to get ...
- Tue Apr 26, 2016 6:01 pm
- Forum: CBoat C Forum
- Topic: Vinyl Adhesive
- Replies: 5
- Views: 7975
Re: Vinyl Adhesive
If you have an Ace Hardware near you, then they should have this. It IS Vynabond. I've used it several times. http://www.acehardware.com/product/inde ... Id=1381659" onclick="window.open(this.href);return false;
- Tue Sep 02, 2014 2:12 am
- Forum: CBoat C Forum
- Topic: What is the most difficult CBoat you've ever paddled?
- Replies: 16
- Views: 28766
Re: What is the most difficult CBoat you've ever paddled?
I'll go with ACE III as well. I never could stay upright in that boat for very long.
I was just fine in a few other Wildwater boats, but not that one...
I built an extrabat that was over cut for my weight - edges were in the water sitting still... there really in no need for a 13'2" Squirt boat
I was just fine in a few other Wildwater boats, but not that one...
I built an extrabat that was over cut for my weight - edges were in the water sitting still... there really in no need for a 13'2" Squirt boat
- Wed Aug 27, 2014 1:32 am
- Forum: CBoat C Forum
- Topic: What is the most difficult CBoat you've ever paddled?
- Replies: 16
- Views: 28766
Re: What is the most difficult CBoat you've ever paddled?
That's what you get for paddling a squirt boat at a weight exceeding the cut;)
Well, except for the Demo Maven. You aren't heavy enough for that one!
I my old ACE III resurfaces try it out... or drop by and try the Oxygen;)
Well, except for the Demo Maven. You aren't heavy enough for that one!
I my old ACE III resurfaces try it out... or drop by and try the Oxygen;)
- Thu Aug 21, 2014 4:21 pm
- Forum: CBoat C Forum
- Topic: What is the most difficult CBoat you've ever paddled?
- Replies: 16
- Views: 28766
Re: What is the most difficult CBoat you've ever paddled?
Running a single Class II rapid in the Maven. Got off water feeling like I had a 6 hr work out. I think the O2 would be just as hard. As for the ACE - never been in it so I take your word on that one Adam.
- Thu Aug 21, 2014 2:32 am
- Forum: CBoat C Forum
- Topic: What is the most difficult CBoat you've ever paddled?
- Replies: 16
- Views: 28766
What is the most difficult CBoat you've ever paddled?
I admit... my used Ace III was by far the most difficult for me... even the Oxygen (and Maven) are easier.
That said, some of the problem may have been the flexing hull. I have a Bala (also a WildWater boat) that is far less terrifying.
That said, some of the problem may have been the flexing hull. I have a Bala (also a WildWater boat) that is far less terrifying.
- Sun May 25, 2014 3:55 am
- Forum: Boats and Gear for Sale
- Topic: Protec helmet & kokotat GFER mens suit
- Replies: 0
- Views: 3172
Protec helmet & kokotat GFER mens suit
Protec Ace Water helmet & Salamander beak visor. Never used, NIB. Carbon color, black beak visor. Size: L/XL. $45.00 plus shipping by cheapest method (usually USPS). Located in NJ, 07506. Weight, 2 lbs. Kokotat Gore-Tex Front ...
- Wed May 14, 2014 3:17 pm
- Forum: CBoat C Forum
- Topic: Tow tether suggestions.
- Replies: 24
- Views: 21559
Re: Tow tether suggestions.
... non-releasable part of your pfd is real. Just don't expose snapgates on the river when there are people involved, ever. The 10 seconds time was an ACE drill, and we had the advantage of having our anchor in place already. As long as your team is properly trained to work together, the attaching ...
- Thu Jan 23, 2014 4:08 pm
- Forum: CBoat C Forum
- Topic: Ace 4.7 as first C boat?
- Replies: 1
- Views: 4070
Re: Ace 4.7 as first C boat?
Go for it. Should be squirty and wave-wheely. Fun with eddy lines! Might be pearly on waves?
- Thu Jan 23, 2014 1:39 pm
- Forum: CBoat C Forum
- Topic: Ace 4.7 as first C boat?
- Replies: 1
- Views: 4070
Ace 4.7 as first C boat?
I've been wanting to convert a boat for my first C1 for a while now. I have an old Ace 4.7 sitting in the garage collecting dust, and I've been toying with the idea of making it my first project. Now, I know there are a lot better boats to convert, but this one is ...